1. Attention

    Fine adjustments apply only to current job.

  2. Inserter Fine Tuning

    1. On the Run screen graphic, press anywhere on the Inserter icon.

      1. Note that each heading expands.

      2. You can change:
        • Seal mode: Turn off to leave envelopes unsealed.
        • Doubles detect: Turn off if thick or dark envelopes give false readings.
        • Separator wear: Adjust separator gap only if needed (1 clock = 0.015mm). This changes the gap on the unit and applies to all jobs: see also Gap Adjust below.
        • Documents: Changes to the envelope depth, width, flap and throat.
        • Wetting: changes the amount of wetting (1-8) where higher numbers give greater wetting.
        • Gap Adjust: Adjusts the separator gap for this document only (1 clock = 0.015mm). Note that this is relative to Separator Wear, and adds to or subtracts from that setting. The setting is saved with this document and remains for future uses.
        • Shield: This controls the amount of shielding over the separator roller, and should not normally require adjustment. However, if stream-feeding or erratic double feeds occur, try moving the shield back (ie. reducing the percentage). If documents are not properly picking up, move it forward. The shield is initially set in the inserter unit setup in the Fine Tuning screen. Adjustments will increment or decrement this initial setting.
      3. Note

        These settings apply only to the information stored with the job named at the top of the dialog box, except for Separator Wear.

      4. When all adjustments are complete, press OK.

  3. Feeder Fine Tuning

    1. On the Run screen graphic, press anywhere on the Feeder icon.

      1. Note that each heading expands.

      2. You can change:

        • Feed control mode: Turn off to disable feeder.
        • Doubles detect: Turn off if thick or dark documents give false readings.
        • Load to Reader (reading units only): this will feed one document into position under the reader. Press Reader On to test the reader, Reader Off to end the test. Remove the document and replace on feed hopper.
        • Separator wear: Adjust separator gap only if needed (1 clock = 0.015mm). This changes the gap on the unit and applies to all jobs: see also Gap Adjust below.
        • Documents: Changes to the insert depth & width.
        • Gap Adjust: Adjusts the separator gap for this document only (1 clock = 0.015mm). Note that this is relative to Separator Wear, and adds to or subtracts from that setting. The setting is saved with this document and remains for future uses.
        • Shield: This controls the amount of shielding over the separator roller, and should not normally require adjustment. However, if stream-feeding or erratic double feeds occur, try moving the shield back (ie. reducing the percentage). If envelopes are not properly picking up, move it forward. The shield is initially set in the inserter unit setup in the Fine Tuning screen. Adjustments will increment or decrement this initial setting.
  4. Folder Fine Tuning

    1. On the Run screen graphic, press anywhere on the Folder icon.

      1. Note that each heading expands.

      2. You can change:
        • Feed control mode: Turn off to disable folder.
        • Doubles detect: Turn off if thick or dark documents give false readings.
        • Address adjust: Adjustment up or down of address position in envelope window.
        • Load to Reader (reading units only): this will feed one document into position under the reader. Press Reader On to test the reader, Reader Off to end the test. Remove the document and replace on feed hopper.
        • Separator wear: Adjust separator gap only if needed (1 clock = 0.015mm). This changes the gap on the unit and applies to all jobs: see also Gap Adjust below.
        • Document: Changes to the insert depth & width.
        • Gap Adjust (clocks): Adjusts the separator gap for this document only (1 clock = 0.015mm). Note that this is relative to Separator Wear, and adds to or subtracts from that setting. The setting is saved with this document and remains for future uses.
  5. Collator Fine Tuning

    1. On the Run screen graphic, press anywhere on the Collator icon.

      1. Note that each heading expands.

      2. You can change:
        • Feed control mode: Turn off to disable folder.
        • Doubles detect: Turn off if thick or dark envelopes give false readings.
        • Address adjust: Adjustment up or down of address position in envelope window.
        • Load to Reader (reading units only): this will feed one document into position under the reader. Press Reader On to test the reader, Reader Off to end the test. Remove the document and replace on feed hopper.
        • Separator wear: Adjust separator gap only if needed (1 clock = 0.015mm). This changes the gap on the unit and applies to all jobs. See also Gap Adjust below.
        • Documents: Changes to the insert depth & width.
        • Gap Adjust: Adjusts the separator gap for this document only (1 clock = 0.015mm). Note that this is relative to Separator Wear, and adds to or subtracts from that setting. The setting is saved with this document and remains for future uses.
Date created:
03/05/2018 07:56:29
Last updated:
03/07/2018 07:43:39
Product(range):
DS-1200 G4i
Print